Manx – a catalogue of online computer manuals
MicroVAX II 630QY, 630QZ Technical Manual
| Company: | Digital Equipment Corporation |
| Part: | AZ-FE06A-TN |
| Date: | 1985-04 |
| Keywords: | |
| Cited by: | |
Table of Contents
- Chapter 1 BA23-A Enclosure
- 1.1 Introduction
- 1.2 BA23-A Frame
- 1.3 Front Control Panel
- 1.3.1 Control Panel Printed Circuit Board
- 1.4 Mass-Storage
- 1.5 Backplane
- 1.5.1 Mass-Storage Signal Distribution Panel
- 1.5.2 H9278 Backplane
- 1.6 Power Supply and Fans
- 1.7 Rear I/O Distribution Panel
- Chapter 2 Base System
- 2.1 Introduction
- 2.2 KA630-A CPU
- 2.2.1 Console Program
- 2.2.2 Primary Bootstrap Program
- 2.2.3 CPU Patch Panel Insert
- 2.3 MS630 Memory Module
- Chapter 3 System Options
- 3.1 Introduction
- 3.1.1 Ordering Options
- 3.1.2 Module Configurations
- 3.2 Communications
- 3.2.1 DEQNA Ethernet Interface
- 3.2.2 DHV11 Asynchronous Multiplexer (eight lines)
- 3.2.3 DLVJ1 Asynchronous Multiplexer (four lines)
- 3.2.4 DMV11 Synchronous Controller
- 3.2.5 DPV11 Synchronous Interface
- 3.2.6 DRV11-J High Density, Parallel Interface (four lines)
- 3.2.7 DZQ11 Asynchronous Multiplexer (four lines)
- 3.2.8 DZV11 Asynchronous Multiplexer (eight lines)
- 3.2.9 LPV11 Interface Module
- 3.3 Disk Storage Devices
- 3.3.1 RQDX2 Disk Controller
- 3.3.2 RD51, RD52, RD53 Disk Drives
- 3.3.2.1 Factory Configuration
- 3.3.3 RX50-AA Diskette Drive
- 3.3.4 RC25 Disk Subsystem
- 3.3.5 TK50 Tape Drive Subsystem
- Chapter 4 Configuration
- 4.1 Configuration Rules
- 4.1.1 Module Physical Priority
- 4.1.2 Expansion Space
- 4.1.3 Power Requirements
- 4.1.4 Bus Loads
- 4.1.5 Module CSR Addresses/Interrupt Vectors
- 4.1.5.1 Floating CSR Addresses
- 4.2 Configuration Examples
- 4.2.1 Base System Configuration
- 4.2.2 Advanced System Configuration
- Chapter 5 Diagnostics
- 5.1 Introduction
- 5.2 KA630 Boot and Diagnostic ROM
- 5.2.1 Power-up Mode
- 5.2.2 Console Mode
- 5.3 Power-up LEDs on Mass Storage, Backup, and Communications devices
- 5.4 MicroVAX Maintenance System
- 5.4.1 Configuration Verification
- 5.4.2 System Tests
- 5.5 Troubleshooting
- 5.5.1 Unknown System Level Problems
- 5.5.2 Device-Specific Problems
- Chapter 6 FRU Removal and Replacment Procedures
- 6.1 Introduction
- 6.2 Control Panel Removal
- 6.3 RX50/TK50 Drive Removal
- 6.3.1 TK50/TQK50 Interconnect Cable Removal and Installation
- 6.4 RD5n Fixed Disk Drive Removal
- 6.4.1 RD51 Disk Drive Read/Write Board Removal
- 6.4.2 RD52 Main Printed Circuit Board Removal
- 6.4.3 RD53 Disk Drive Device Electronics Board Removal
- 6.4.4 RD5n/RDQX Interconnect Cable Removal and Installation
- 6.5 Backplane Assembly Removal
- 6.6 Power Supply (H7864-A) Removal
- 6.7 Rear Cooling Fan Removal
- 6.8 Front Fan Removal
- 6.9 Module Removal
- 6.10 Rear I/O Insert Panel Removal
- 6.11 Time of Year Clock Battery Backup Removal
- Appendix A Console Commands
- Appendix B Console Error Messages and Explanations